Stop Nuisance Calls with Call Blocklist/Allowlist Feature on Yeastar PBX

Unwanted calls can be a real nuisance, which is inconvenient and annoying at the best of times, especially for the elderly or vulnerable it can be quite frightening. It is a “plague” not only for individuals but also for companies. Mobile phone users can install some blocking Apps to filter and block specific numbers easily, however, for companies, how to protect extensions from this nuisance?

With Blocklist/Allowlist feature, Yeastar S-Series VoIP PBX (on-premises) and Cloud PBX can easily help you get rid of them once and for all. In this blog posts, we’ll give a comprehensive introduction into this feature, about how it works and how to configure the feature on Yeastar PBX.

1. Call Blocklist

The blocklist feature of Yeastar PBX functions similarly to call blocker apps on your mobile phone, but there are still some differences.

Call Blocklist on the Yeastar PBX is used to block incoming and/or outgoing calls. If you list a phone number of the incoming call in the blocklist, you will not receive the call from this number any longer. And the caller will hear the following prompt: “The number you have dialed is not in service. Please check the number and try again”. The system will then disconnect the call. Likewise, if you list the phone number of the outgoing call in the blocklist, you can not dial that number any longer.

Blocklist groups

Nuisance calls are varied and usually attempt to promote a product, service to you, or even defraud you. Categorizing the blocklist call by name will greatly help companies optimize phone management.

Block Calls with Number Segment

It can be easily found that lots of nuisance calls are of same number segments. In this case, you can use the wildcard matching to flexibly block the phone number with specific segments by setting call blocklist rules.

For example, if you enter “400.” (where wildcard “.” matches anything remaining) in the number field as below, all unknown numbers of any length beginning with 400 will be blocked. While entering “95XXX!” (where “X” matches the number 0-9 and wildcard “!” causes the matching process to complete), all five-digit numbers beginning with 95 will be blocked.

Note: the wildcard rules are defined by the PBX System by default.

Blocklist Types

In addition to some unwanted calls, you may also encounter “one ring call”. If your phone rings once, then stop, think very carefully before calling that number back because your phone may face high charges. Such “ring-back” or “ one-ring” scams have long plagued the telecom world. With Yeastar Cloud PBX or S-Series VoIP PBX, you can also prohibit your extensions to make outgoing calls to these numbers to avoid huge losses.

Yeastar VoIP PBX system supports to block or allow 3 types of calls/numbers:

• Inbound: The number would be disallowed or allowed to call in the PBX system.
• Outbound: Extension users are disallowed or allowed to call the number out from the PBX system.
• Both: Both inbound and outbound calls of the number are disallowed or allowed.

2. Call Allowlist

You probably meet a problem that the number segments of your customers’ phone numbers happen to be listed in the blocklist. If so, how to deal with it?

Allowlist feature of Yeastar Cloud PBX and S-Series IP PBX allows you to add trusted incoming/outgoing numbers that have higher priority than the blocklist.

For example, we listed all phone numbers beginning with 400 in the blocklist via the “400.” blocklist rule, however, your customers’ phone number happens to be 4005915259. Simply by adding this number in your allowlist, you can make/receive calls from this number while blocking other numbers started with “400”.

 

You might be also interested in:

In addition to the blocklist/allowlist feature, Yeastar IP PBX also provides auto call recording feature to automatically save the conversations of the fraud calls. This can provide dependable evidence for tracing the criminals.

You can also gain a comprehensive into Yeastar VoIP PBX features here. We not only list the features but also explain each with uses case, configuration video guides and etc.

This blog was originally published on Nov.15, 2016 and updated on Apr.18, 2019.

This Post Has 4 Comments

1. how to block call from “Unknown” number ?

   Reply

   1. Hi Dendi,
      Blocking calls from unknown numbers in your phones, you can click here for reference. Blocking calls from unknown numbers in PBX, you can refer to the post.

      Reply

2. I think dendi is trying to say, and I also want to know, how can I block an unknown number, when no number appears on the screen? But at the same time, letting in calls from numbers that I don’t have on the list

   Reply

   1. Hi Fran, to solve the problem, you can edit inbound route, adding “X.” and “+X” into Caller ID pattern therefore the unknown ID will be blocked automatically. For more details, you can send mail to this address helpdesk@yeastar.com. Our support team will help you asap.

      Reply

Leave a Reply Cancel comment reply

Your email address will not be published. Required fields are marked *

Name *

Email *

Website

Save my name, email, and website in this browser for the next time I comment.

Comment